In the specific application of quartz stone, it is unavoidable to splice two pieces or even multiple pieces. Since the hardness of the quartz stone plate is as high as Mohs hardness level 7, after splicing, in order to make the whole look integrated, it will test the skills of the quartz stone manufacturer and the processing master. . For specific operations, we can operate in the following ways.
China quartz countertops with sparkle
Perform mutual inspections on all large and small materials. The contents of the mutual inspection include the direction of the skirt, the position of the edging, the direction of the bevel, the length and width of the skirt and the small material, and whether there is any joint between the panel’s Chromatic aberration. Before making it, you must understand the edge structure and small material specifications of the countertop, and be aware of it, and don’t stick to the wrong edge.
Place the bottom surface of the panel on the workbench, check the flatness of the surface to be bonded, wipe off the stained area with a cleaning ball, rinse with water, use an air gun or dry cloth to clean and dry the surface to be bonded. According to the thickness of the countertop, choose the skirt reinforcement strip of the corresponding height, and evenly apply the toning marble glue to bond the reinforcement strip to the bottom of the countertop with the smooth surface of the reinforcement strip inward, and the outer edge of the reinforcement strip is flush with the bevel edge of the panel. Clamp it with a g-type clamp or a-type clamp to clear the remaining glue. Evenly apply the color marble glue to the inclined surface of the panel and the side of the reinforcing strip. Place the inclined surface of the skirt on the glue and rub it left and right to squeeze out the air. Use the F clamp to clamp the skirt and the panel, and use a rubber hammer to moderate Tap with the intensity to make the skirt and the corner of the panel even, and clamp a clip every 100-150mm. Then clamp the skirt and the reinforcing plate with A-shaped clamps between every two F-shaped clamps to clean up the residual glue. Stick a flat light-facing outward slat flush with the bottom of the reinforcing plate to make the width of the skirt reach 65mm, and fix it with clamps every 200mm.
Factory kitchen countertops quartz cost
Place the bottom of the panel up on the workbench, check the flatness of the surface to be bonded, wipe off the stained area with a cleaning ball, rinse with water, use an air gun or dry cloth to clean and dry the surface to be bonded. According to the thickness of the countertop, choose a skirt reinforcement block of the corresponding height (the specification of the reinforcement block is 35×h, h=h-2d), and evenly apply the color marble glue to bond the reinforcement block to the bottom of the countertop every 200mm. The outer edge of the reinforcement box is flush with the hypotenuse of the panel. Clamp with g-clamp or a-clamp to remove residual glue. Evenly spread the color marble glue on the bevel of the panel and the side of the reinforcement strip, put the bevel of the skirt on the glue, and rub it left and right to squeeze out the air. Clamp the skirt and the panel with an F-clamp, and use a rubber hammer to moderate Tap with a strong force to make the skirt and the corner of the panel level, and clamp a clip every 100-150mm away. Then clamp the skirt and the reinforcement block with a g-clamp between every two f-clamps to clean up the remaining glue. Stick a flat light-facing outward slat flush with the bottom of the reinforcing plate to make the width of the skirt reach 65mm, and fix it with clamps every 200mm.
Yellow gold quartz countertops
Place the bottom surface of the panel up on the workbench, check the flatness of the surface to be bonded, wipe off the stained area with a cleaning ball, rinse with water, and clean and dry the surface to be bonded with an air gun or dry cloth. Evenly spread the color marble glue on the inclined surface of the panel and the side of the reinforcing strip put the inclined surface of the skirt on the glue and rub it left and right to squeeze out the air. Use a clamp to clamp the skirt and the panel, and use a rubber hammer to moderate Tap with a strong force to make the skirt and the corner of the panel level, and clamp a clip every 100-150mm away. Clean up the remaining glue and enter the next process after 15 minutes.
