In the specific application of quartz stone, it is inevitable to splice two pieces or even multiple pieces. As the hardness of the quartz stone plate is as high as 7 Mohs hardness, after splicing, in order to make the whole seem integrated, it will test the quartz stone manufacturers and processing masters. technology. For specific operations, we can click the method to operate.
China faux quartz countertops
Perform mutual inspections on all large and small materials. The content of the mutual inspection includes the direction of the skirt, the position of the edging, the direction of the bevel, the length and width of the skirt and the small material, and whether there is any joint between the panels Chromatic aberration. Before making it, you must understand the edge structure and small material specifications of the countertop, and be aware of it, and don’t stick the wrong edge.
Place the bottom surface of the panel up on the workbench, check the flatness of the surface to be bonded, wipe off the stained area with a cleaning ball, rinse with water, use an air gun, or dry cloth to clean and dry the surface to be bonded. According to the thickness of the countertop, select the skirt reinforcement strip of the corresponding height (the height of the reinforcement strip h=h-d), and evenly apply the color-tone marble glue to bond the reinforcement strip inward to the bottom of the countertop. The outer edge of the reinforcement strip and the panel The hypotenuse is flush. Clamp it with a g-type clamp or a-type clamp to clear the remaining glue. Spread the color marble glue evenly on the inclined surface of the panel and the side of the reinforcing strip. Place the inclined surface of the skirt on the glue and move it left and right to squeeze out the air. Use the F clamp to clamp the skirt and the panel, and use a rubber hammer to moderate The strength of the light tap is that the skirt is flush with the corner of the panel, and a clip is clamped every 100-150mm. Then clamp the skirt and the reinforcing plate with an A-type clamp between every two F-type clamps to clean up the residual glue. Stick a flat light-facing outward slat flush with the bottom of the reinforcement class to make the width of the skirt reach 65mm, and fix it with clips every 200mm.
Factory sealing quartz countertops
Place the bottom of the panel up on the workbench, check the flatness of the surface to be bonded, wipe off the stained area with a cleaning ball, rinse with water, use an air gun, or dry cloth to clean and dry the surface to be bonded. According to the thickness of the countertop, choose a skirt reinforcement block of the corresponding height (the specification of the reinforcement block is 35×h, h=h-2d), and evenly apply the color marble glue to bond the reinforcement block to the bottom of the countertop every 200mm. The outer edge of the reinforcement box is flush with the hypotenuse of the panel. Clamp it with a g-type clamp or a-type clamp to clear the remaining glue. Evenly spread the color marble glue on the inclined surface of the panel and the side of the reinforcement strip, put the inclined surface of the skirt on the glue, and rub it left and right to squeeze out the air. Clamp the skirt and the panel with an F-clamp, and use a rubber hammer to moderate Tap with the intensity to make the skirt and the corner of the panel level, and clamp a clip every 100-150mm. Then clamp the skirt and the reinforcement block with a g-clamp between every two f-clamps to clean up the remaining glue. Glue a flat light-facing outward slat flush with the bottom of the reinforcing plate to make the width of the skirt reach 65mm and fix it with clips every 200mm.
White sparkle quartz countertops
Place the panel ground up on the workbench, check the flatness of the surface to be bonded, wipe off the stained area with a cleaning ball, rinse with water, use an air gun or dry cloth to clean and dry the surface to be bonded. Evenly spread the color marble glue on the inclined surface of the panel and the side of the reinforcing strip. Place the inclined surface of the skirt on the glue and rub it left and right to squeeze out the air. Use a clamp to clamp the skirt and the panel, and use a rubber hammer to moderate Tap with the intensity to make the skirt and the corner of the panel level, and clamp a clip every 100-150mm. Clean up the remaining glue and enter the next process after 15 minutes.
